Professional heating, cooling & air quality services serving Provo and surrounding communities in Utah. NATE-certified, 24/7 emergency response.
NATE-certified technicians providing the complete range of heating and cooling services.
Professional smart thermostat installation goes beyond mounting and Wi-Fi pairing. Technicians verify your system has the necessary common wire, confirm compatibility with multi-stage heating and cooling equipment, and program setpoints and schedules tailored to your household for immediate energy savings.
Restoring reliable air conditioning performance requires more than replacing visible parts. Technicians measure refrigerant pressures, check compressor winding resistance, test run and start capacitors, and verify condenser fan operation to ensure every component of the cooling circuit functions within specification.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Over time, air ducts accumulate dust, pet dander, mold spores, and construction debris that degrade indoor air quality and restrict airflow. Professional duct cleaning uses negative-pressure HEPA-filtered vacuums and rotary brush systems to remove contaminants from supply and return plenums.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Mini-split repair demands familiarity with variable-speed compressor technology and manufacturer-specific diagnostic protocols from Mitsubishi, Fujitsu, Daikin, and LG. Technicians trace electrical faults, recharge refrigerant to factory specifications, and replace condensate pumps to restore silent, efficient operation.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
Restoring heat pump performance starts with accurate diagnostics of compressor function, reversing valve operation, and refrigerant charge levels. Our NATE-certified technicians service all major brands including Carrier, Trane, Lennox, and Rheem to resolve airflow loss, short cycling, and defrost failures.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
A city of 115,666 residents generates significant demand for emergency HVAC services, especially during extreme weather events and seasonal transitions when systems are stressed to their limits. KIC Refrigeration maintains the crew capacity, parts inventory, and dispatch infrastructure to respond to multiple emergencies simultaneously across Provo when conditions demand it.
We have responded to every type of HVAC emergency across Provo, and that experience informs every diagnostic decision we make on-site. From compressor failures and heat exchanger cracks to frozen evaporator coils and tripped high-limit switches, our techniques are optimized for the equipment brands, duct configurations, and climate demands that Provo systems face year after year.
What makes us different from every other heating and cooling company in the area.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Our technicians live and work in the communities they serve. They understand local building codes, climate demands, utility rebate programs, and the HVAC challenges specific to your area. Local expertise backed by a nationwide service network means fast response and consistent quality everywhere.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Get the information you need to make confident HVAC decisions for your property.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Provo, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Provo and surrounding Utah communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
Most residential HVAC installations in Provo, UT are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
HVAC repair costs in Provo typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
A comprehensive HVAC inspection from KIC Refrigeration in Provo covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
The National Air Duct Cleaners Association recommends professional duct cleaning every 3 to 5 years for most Provo homes. However, several factors can shorten that interval: households with pets that shed, family members with allergies or asthma, smokers in the home, and properties that have undergone recent renovation or construction work should consider cleaning every 2 to 3 years. Warning signs that your ducts need attention include visible dust or debris accumulating at register openings, musty or stale odors when the system runs, unexplained respiratory symptoms, and inconsistent airflow between rooms. Our NADCA-compliant cleaning process uses truck-mounted vacuum equipment and rotary brush agitation to remove dust, allergens, mold spores, and debris from your entire duct system. We also inspect for disconnected joints, damaged insulation, and air leaks that reduce system efficiency.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"Our mini split stopped cooling mid-summer and they fit us in the next morning. Diagnosed a bad capacitor, replaced it on the spot. Back to normal in under an hour."
"Boiler kept cycling on and off. Technician found a faulty thermocouple and replaced it on the spot. No nonsense, no upselling. Just good honest work."
"Had our air ducts cleaned and I cannot believe how much dust and debris they pulled out. The air quality in our home improved immediately."
Our NATE-certified crews provide HVAC service throughout the surrounding area.